KFD2-SD-Ex1.48

Output signal		These values are valid for the rated operating voltage 20 ... 35 V DC.
Directive conformity
Electromagnetic compatibility
	Directive 89/336/EEC	EN 61326, EN 50081-2
Conformity
Electromagnetic compatibility		NE 21
Protection degree		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Protection degree		IP20
Mass		approx. 100 g
Dimensions		20 x 107 x 115 mm (0.8 x 4.2 x 4.5 in)
Data for application in connection with Ex-areas
EC-Type Examination Certificate		BAS 00 ATEX 7216 , for additional certificates see www.pepperl-fuchs.com
	Group, category, type of protection	II (1)GD [EEx ia] IIC (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2]
Statement of conformity		TÜV 99 ATEX 1499 X , observe statement of conformity
	Group, category, type of protection, temperature class	II 3G EEx nA II T4 [device in zone 2]
Directive conformity
	Directive 94/9/EC	EN 50014, EN 50020, EN 50021

1、安全柵應安裝在非危險場所。
2、安全柵通往現場(危險場所)的軟銅導線截面積必須大于0.5mm²。
3、連接導線的絕緣強度大于500V。
4、安全柵本安端(有藍色標記)和非本安端電路配線，不得接錯和混淆。本安導線宜選用藍色作為本安標記。本安導線和非本安導線在匯線槽中應分開鋪設，采用各自保護套管。安全
柵的本安側，不允許混淆有其它電源，包括其它本安電路的電源。
5、安全柵與一次儀表組成本安安全防爆系統時，必須經國家指定的防爆檢驗機構檢驗認可。PH系列安全柵安全柵由國家防爆電氣監督檢驗中心，給出的Co，Lo分布參數是相對與ⅡC級(氫氣級)的最大允許值對于ⅡB級環境可把該參數乘以3，對于ⅡA級環境可把該參數乘以8。傳輸線選用不同規格的電纜時，其本身的電纜參數應予高度重視，不得超過規定值。
6、對安全柵進行單獨通電調試時，必須注意安全柵的型號、電源極性、電壓等級及安全柵外殼接線端上的標號。
7、嚴禁用兆歐表測試隔離安全柵端子之間的絕緣性。若要檢查系統線路絕緣性時，應先斷開全部安全柵接線，否則會引起內部器件損壞。

current limit 35 mA
Supply
Rated voltage		loop powered
Power loss		1.3 W
Input
Connection		terminals 7+, 8-
Rated voltage		5 ... 35 V DC
Current		6 mA at 18.5 V nominal supply voltage, 70 mA at 35 V nominal supply voltage
Output
Internal resistor		max. 303 Ω
Limit		current IE: min. 35.3 mA voltage UE: 12.1 V
Open loop voltage		min. 22.8 V
Connection		terminals 1+, 2-
Output rated operating current		35 mA
Output signal		These values are valid for the rated operating voltage 20 ... 35 V DC.
Directive conformity
Electromagnetic compatibility
	Directive 89/336/EEC	EN 61326, EN 50081-2
Conformity
Electromagnetic compatibility		NE 21
Protection degree		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Protection degree		IP20
Mass		approx. 100 g
Dimensions		20 x 107 x 115 mm (0.8 x 4.2 x 4.5 in)
Data for application in connection with Ex-areas
EC-Type Examination Certificate		BAS 00 ATEX 7216 , for additional certificates see www.pepperl-fuchs.com
	Group, category, type of protection	II (1)GD [EEx ia] IIC (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2]
Statement of conformity		TÜV 99 ATEX 1499 X , observe statement of conformity
	Group, category, type of protection, temperature class	II 3G EEx nA II T4 [device in zone 2]
Directive conformity
	Directive 94/9/EC	EN 50014, EN 50020, EN 50021